How to restore motorcycle meter cover/cluster | how to change meter cover | repair meter |pulsar 150

How to restore motorcycle meter cover/cluster | how to change meter cover | repair meter |pulsar 150

Namaskar dosto welcome to sai repair today’s video is about meter cover also known as meter cluster if the meter cover got broken in accident or by other means as you see in my case visor got cracked and so is the meter cover got cracked if you don’t change it timely the meter components

When to change gear in a manual/stick shift car. Changing gears tips. Learning to drive.

When to change gear in a manual/stick shift car. Changing gears tips. Learning to drive.

Hello I’m Chris. On one of our previous videos, we had a look at how to position your hand correctly on the gear stick using the palming method. In this video I will show what to do with your feet and when to change gears in a manual car. But why do we need to

HOW TO REPLACE DRUM BRAKE SHOES+CHANGE WHEEL CYLINDER IN DETAIL|DIY FULL REAR SERVICE FIX+ADJUST

HOW TO REPLACE DRUM BRAKE SHOES+CHANGE WHEEL CYLINDER IN DETAIL|DIY FULL REAR SERVICE FIX+ADJUST

Hello, this is GeRAMicc85. Today I’m showing how I replace the brake shoes and wheel brake cylinder of the drum brakes on my Dodge Ram 1500. This is an 11 inch drum brake on a 9 1/4 inch axle used on a Dodge / Chrysler / Jeep and others. I noticed that there were oily

How to Replace the Drum Support Wheel on a Candy Tumble Dryer

How to Replace the Drum Support Wheel on a Candy Tumble Dryer

Hi, I’m Mat from eSpares. In this video, I’ll be replacing the drum support wheel on this Candy tumble dryer. If your tumble dryer has become noisy when the drum turns then it is likely that the drum support wheel has failed and it needs to be replaced. Safety first always disconnect an appliance before

Changing a caravan jockey wheel

Changing a caravan jockey wheel

Hi everyone, welcome back I hope you are all well In this video we will be changing our jockey wheel And this video is showing you how you can replace your jockey wheel if you find you need to It may not be overtly obvious on how you can do that and also depending on

How to Replace Your Motorcycle Brake Lever and Motorcycle Clutch Lever

How to Replace Your Motorcycle Brake Lever and Motorcycle Clutch Lever

Replacing the stock levers on a bike is a cheap way to improve ergonomics and feel for the bike, especially if your stock levers offer no adjustment. Tools you’ll need are a wrench, lubricant, grease, flat head screwdriver and allen keys. We’ll do the easy one first, the brake lever. Unscrew the retaining bolt from

Motorcycle Steering Stem Bearing Replacement

Motorcycle Steering Stem Bearing Replacement

In this video, we’ll demonstrate how to properly remove worn out steering stem bearings. We’ll also show you how to pack your new bearings with grease and install them onto your bike. These steps can be used to help you replace the steering stem bearings on just about any bike. Keep in mind the process

How to switch the visor on your HJC motorcycle helmet

How to switch the visor on your HJC motorcycle helmet

Alright today I’m going to show you how to remove the visor and replace it on a CS-R2 helmet. This is the matte black version. Anyway just take the visor, lift it all the way up, and then right here there’s this little thing that you press. And then the visor itself will lift up

Motorcycle Top End Rebuild for 4-Stroke (Part 2 of 2)

Motorcycle Top End Rebuild for 4-Stroke (Part 2 of 2)

This is part two of our KTM 4-stroke top-end piston and ring replacement. In our last video, during disassembly, we discovered we needed a new sleeve, and we sent it off to L.A. Sleeve. They were able to get it back to us good as new. We’re going to install a Wiseco piston, and the